Please sign in or register to stay updated about this part.
The PI3EQX1002B is a low-power, high-performance 10Gbps 1-Port USB3.1 Linear ReDriver™ designed specifically for the USB3.1 protocol. The device provides programmable equalization, linear swing and flat gain to optimize performance over a variety of physical mediums by reducing Inter-Symbol Interference. PI3EQX1002B supports two 100Ω Differential CML data I/O’s between the Protocol ASIC to a switch fabric, over cable, or to extend the signals across other distant data pathways on the user’s platform. The integrated equalization circuitry provides flexibility with signal integrity of the signal before the ReDriver. Each channel operates fully independently. The channels’ input signal level determines whether the output is active. The PI3EQX1002B also includes an automatic receiver detect function. The receiver detection loop will be active again if the corresponding channel’s signal detector is idle for longer than 7.3mS. The channel will then move to Unplug Mode if load not detected, or it will return to Low Power Mode (Slumber Mode) due to inactivity. This USB3.1 ReDriver removes and clean-out Jitter and conditions the signal.
Is Pericom's USB3.0 ReDriver™ compatible with USB2.0?
No. USB 3.0 uses different connect pins from USB 2.0's. The USB 3.0 Standard-B receptacle interfaces are divided into two sets of interfaces: the USB 2.0 interface and the USB 3.0 SuperSpeed interface. The USB 2.0 interface is comprised of pins 1 to 4, and the USB 3.0 SuperSpeed interface is comprised of pins 5 to 9. The figure below shows the footprint of USB3.0 found in "Universal Serial Bus 3.0 Specification Version 1.0_Page 5-19_Figure5-8".
Is there any Application Notes for PCIe ReDrivers?
Yes, AN088 and AN233 are Application Notes for PCIe ReDrivers.
Is there any pull up/down resistor needed on Dual Mode DP Source Device on Pin 13 of cable adaptor detect?
1Mohm pull down resistor on Pin 13 is needed on Dual Mode DP Source Device.
What are the types of jitter?
There are several types of jitter, but the main ones are: cycle-to-cycle jitter, period jitter, half period jitter, and peak-to-peak jitter. Jitter terminology can be found in AB36: Jitter Measurement Techniques at Application Brief No. 36 or Application Note No. 27.
What controls are provided by the PCIe ReDriver?
Both I2C and GPIO controls are provided.
What does de-emphasis control mean?
Emphasis control can improve USB3.0 ReDriver's output signal. The integrated de-emphasis circuitry provides flexibility and improves the integrity of USB3.0 output signal after ReDriver. The de-emphasis selection table below describes pin strapping options and associated de-emphasis operations. This table can be found in datasheet, page 3.
What does emphasis control mean?
Emphasis control improves the PCIe ReDriver output signal.
What does EQ control mean?
EQ control can improve the USB3.0 ReDriver's input signal. The integrated equalization circuitry provides flexibility and improves the integrity of the USB3.0 input signal before the ReDriver. The Equalizer Selection table below describes pin strapping options and associated operations of the equalizer. This table can be found in PI3EQX7741AI datasheet, page 3.
What does swing control mean?
Swing control can adjust the ReDriver IC output swing level.
What is cycle-to-cycle jitter?
Cycle-to-cycle jitter is the difference in the clock's period between two consecutive cycles and is expressed in units of + pico-seconds. This is because it can be either leading or lagging from the ideal output waveform.
What is the application suitability comparison between a switch and a logic driver?
A switch is a passive device with C-on and R-on that will attenuate the signal. A logic driver is an active device that will refresh an input signal at output by its active driving ability. Thus, compared to a logic driver, the maximum frequency of an application using a switch is limited by the trace length and the capacitive load. It is recommended to use a logic driver for applications with heavy capacitive load, long trace and high frequency.
What is the impedance range for USB3.0?
The range of the impedance is from 75Ω to 105Ω.
What is the lead finish for Pericom products? What about lead-free?
All Pericom's products that are not lead-free are composed of 85% Sn and 15% Pb. For lead-free products, they are composed of 100% matte Sn. Lead-free products are marked and ordered with the letter "E" suffix at the end of the part number.
What is the minimum input swing level that a Pericom PCIe ReDriver can accept?
The minimum input swing level is shown in the specification "CML input Differential Input Peak-to-peak Voltage" and some ReDrivers can automatically select the input threshold voltage.
What is the significance of the EQ control?
EQ control can improve the PCIe ReDriver input signal.
When the client-side returns a feedback packet to the host side, will Pericom's PCIe ReDriver block the packet or require control?
No, Pericom PCIe ReDriver will not block any PCIe signals. The ReDriver only enhances gains of the data voltage without changing the data. The host always sees the end-point directly. Pericom ReDriver is "100% transparent", which means the "host" and "end-point" do not detect the presence of the ReDriver.
Where can I find Mean Time Before Failure (MTBF) or Failures In Time (FIT) values for Pericom products?
FIT and MTBF data can be found at Pericom's Quality webpage.
Where can I find the information on your Pb-free and "Green" packaging?